CyberPower BR450ELCD Bedienungsanleitung PDF herunterladen

BR450ELCD/BR650ELCD/BR850ELCD

User’s Manual

K01-0000056-00

SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to unpack,

install, or operate your UPS.

This equipment can be operated by any individuals with no previous training.

The socket-outlet shall be installed near the equipment and easily accessible.

During the installation of this equipment it should be assured that the sum of the leakage currents of the

UPS and the connected loads does not exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from the mains,

hazardous voltage still may be accessible through supply from battery. The battery supply should be

therefore disconnected in the plus and minus pole at the quick connectors of the battery when

maintenance or service work inside the UPS is necessary.

Do not dispose of batteries in a fire, the battery may explode.

Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(1)UPS Unit¯1; (1)Phone Line¯1;(3)USB Cable¯1;(4)User Manual¯1;(5)Management software

Disk¯1;(6)Green Power Technology description¯1;(7)Battery Charger¯1;(8)Cable Collector¯1

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS

unit’s rated capacity (450VA/270W for BR450ELCD, 650VA/390W for BR650ELCD, 850VA/510W for

BR850ELCD). If rated unit capacities are exceeded, an overload condition may occur and cause the

UPS unit to shut down or the fuse blow.

2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert

Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only

calculates the maximum amount of VA that the equipment can use, not what is typically used by the

equipment at any one time. Users should expect usage requirements to be approximately 60% of

below value.

TO ESTIMATE POWER REQUIREMENTS

Watts (W) x 1.67 = VA or Amps (A) x 230 = VA

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual

requirements. There are many factors that can affect the amount of power that your computer system

will require. Suggest the total load to be placed on the battery-powered outlets should not exceed

80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

Before installation, please

read and understand the following instructions:

1. Placement

The UPS must be installed in a protected environment away from heat- emitting appliances such

as a radiator or heat register. Do not install this product where excessive moisture is present.

2. Ventilation

The location should provide adequate air flow around the UPS with one inch minimum clearance

on all sides for proper ventilation.

3. Charge the Battery

Your new UPS may be used immediately upon receipt. However charge loss may occur during

shipping and storage. So charging the battery for at least 8 hours is recommended to insure that

the battery is fully charged. (To recharge the battery, simply leave the unit plugged into an AC

outlet.)

This UPS can be charged even when UPS is not turn on.

4. Connect to AC

Use power cord to connect

the UPS to a wall outlet. Please avoid

using extension cords and adapter

plugs. (To maintain optimal battery

charge, leave the UPS plugged in at

all times.)

5. Connect the Load

Connect the equipment to your UPS

outlets. The IEC power cord coming

with the unit are used to connect your

computer and monitor to the UPS.

Items such as copiers, laser

printers, vacuums, space heaters,

or other large electrical devices

SHOULD NOT be connected to the

UPS. Please make sure that the total

loads of your equipments are less than the maximum total power load of your UPS.

6. Connect to Computer

Install your software and accessories. To use the software, simply use the USB cable to connect

the UPS unit and your computer.

BASIC OPERATION

1. Power On/Off Switch

Press the power switch to turn the UPS ON or OFF.

2. LCD Function Selected Switch

Press the LCD function selected switch to know the UPS status.

3. LCD Display

The LCD will display the UPS status including input voltage, output voltage, runtime, percentage of

load and battery…etc.

4. Communication Protection Ports RJ11/RJ45

Communication protection ports will protect any standard modem, fax, telephone line, or network

cable from surge and spikes.

5. Battery Charger port

Charge external AA/AAA battery via battery charger port with battery charger.

6. AC outlet

The UPS provides 3 outlets for connected equipment to insure temporary uninterrupted operation

during a power failure and against surges and spikes and another 3 outlets against surges and spikes

only.

7. USB Port to PC

This port allows connection and communication

from the USB port on the computer to the UPS

unit. The UPS communicates its status to the

PowerPanel

Personal Edition software. This

interface is also compatible with the UPS service

provided by Windows NT, Windows 2000,

Windows XP, Windows Vista. Mac OSX, Linux.

8. Input Circuit Breaker

The Circuit Breaker provides optimal overload protection.

9 Power on LED

The power on LED lights up when the UPS is ON.

10 Cable Collector

Collect the cables connected from the AC outlets in the cable collector.

11 Battery Charger

Put external AA/AAA batteries into the battery charger for charge.

1 2

User’s Manual 1

Inhaltsverzeichnis

Seite 1 - User’s Manual

BR450ELCD/BR650ELCD/BR850ELCD User’s Manual K01-0000056-00 SAFETY WARNINGS (SAVE THESE INSTRUCTIONS) This manual contains impo

Seite 2

Functional Test AC Mode The UPS delivers power to the loads derived from the utility and maintains proper battery charge. It also regulates the o

Kommentare zu diesen Handbüchern

Keine Kommentare

CyberPower BR450ELCD Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Unterbrechungsfreie Stromversorgungen (USVs) CyberPower BR450ELCD herunter. CyberPower BR450ELCD Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Unterbrechungsfreie Stromversorgungen (USVs) CyberPower BR450ELCD